Ge Microwave Keypad Shorted Service May Be Needed
Bill Newberry 214,020 views 3:32 GE Microwave Repaired -- TCO of JVM1740DM1WW -- Saved 400 dollars - Duration: 4:52. This morning, when they were not working, I applied a sponge soaked with hot water to the touchpad a couple of times, and they worked! Add to Want to watch this again later? Lisa is correct, they are replacing our unit…and/or offering a very good deal on an upgrade! Check This Out
I replaced the circuit board, being careful to position it properly, and tightened the screws. All mine needed was to be unplugged and re plugged in. Reply Barry DeMillion says: July 7, 2014 at 9:09 pm THANKS!!!! I can't see any. Use tip about hairdryer and worked like magic, thanks Tom April 2014 I have done it, in the process to clean the strip I accidently damaged those lines on strip
Ge Microwave Keypad Shorted Service May Be Needed
Remove 2 screws from fan guard and slide off. How do I test whether my microwave is performing properly? Reply John Helm says: July 7, 2014 at 10:41 pm thank-you Lisa!!!
Reply aggieman1125 says: July 8, 2014 at 2:01 am Just called consumer relations (800-836-1215) and was given the runaround. Simply use a warm/hot damp cloth and wipe over the buttons a few times. It had been stored in the hot travel trailer for awhile while not being used. Lg Microwave Touchpad Not Working Thanks, and if it does not hold I will be calling GE like the ladies above.
RepairClinic.com 10,521 views 4:12 How to Diagnose and Fix Your Under Cabinet Microwave. Ge Microwave Control Panel Replacement Loading... Then, they should reattach the wires and replace the cover. Sharp R-209B Allan October 2011 I thought I'd give this a go.
Jim's Good Stuff 4,033 views 2:12 GE Cafe Microwave Touchpad Failure and Possible Solution. - Duration: 7:28. Ge Profile Oven Touchpad Not Working Kitchen Appliances, Microwaves (2421 other questions) Related questions - some, microwave, not, working Add a question Mend > Microwaves Some of buttons on microwave touchpad not working?Some of the touchpad buttons Dale Reply JD Guckenberger says: July 7, 2014 at 11:39 pm Thank you!!! Loading...
Ge Microwave Control Panel Replacement
YOU ARE A BLESSING. Reply Matt Wilson says: July 7, 2014 at 5:57 pm Thanks! http://asktheappliancerepairguy.com/microwave-repair/ge-cafe-microwave-touchpad-failure-and-possible-solution/ He said he will get back to me by Wednesday due to systems down and can not verify if my model with touch pad malfunction qualifies for anything! Ge Microwave Keypad Shorted Service May Be Needed Thanks! Reply outdors1 says: July 7, 2014 at 8:42 pm You saved me a lot of money. Jvm2070sk02 Touchpad Not Working How can I tell if the vent on my Spacemaker™ over-the-range microwave is working correctly?
Reply magic9418 says: July 7, 2014 at 6:50 pm Only worked for a day, Ge is replacing it thanks Lisa for the info Reply Glen Currie says: July 7, 2014 at http://pfntech.com/not-working/clipboard-service.html After spending almost 2 hours with customer relations on both US and Canada sides, I draw a conclusion that GE as a corporate, is really poorly managed. Watch Queue Queue __count__/__total__ Find out whyClose How to repair a GE microwave keypad tonydlc77 SubscribeSubscribedUnsubscribe99 Loading... Loading... Ge Cafe Microwave Recall
Reply BLT822 says: July 8, 2014 at 12:18 am Called the number today that Lisa kindly posted and spoke with Brent. do you know someone with a microwave like yours , you can borrow there keypad from , for a test ? (that request will weed out the fair weather friends real I hate this dreadful microwave and other appliances in the cafe series they are overpriced unreliable pieces of trash. http://pfntech.com/not-working/frigidaire-oven-keypad-not-working.html Sign in to make your opinion count.
The pad was bowed to the inside so I bowed it to the outside while holding each end. Ge Profile Spacemaker 2.0 Microwave If I can get the power level to work, Pin 3 is OK and the solution must be the controller. I can't believe how cheap these are getting.
Now my digits 2, 6, 0 are back to live.
Sign in Share More Report Need to report the video? whatwherethere 29,043 views 1:35 Keypad Repair - Duration: 6:50. The system returned: (22) Invalid argument The remote host or network may be down. General Electric Microwave Troubleshooting My question is not found in these FAQs.
It appears that vibration from the fan as well as closing the microwave door over time causes loose connection in the panel circuit, which causes the touchpad to stop working. You have to hold the cancel button down for three seconds to disable the feature. The paint inside my microwave is chipped or scorched. navigate here Loading...
Reply kitcat says: July 7, 2014 at 11:09 pm This did not work for me. Cheers! Michael Kersey August 2008 Tweet Add An Answer Form Add your answer using the form below ... My microwave is displaying "PF" or "8888." What do I do?
It is $89. Close Yeah, keep it Undo Close This video is unavailable. A soft reset simply backs users out of the programming that is active on the display screen of the microwave. I disconnected some of the other connectors and reconnected but it did not work.
Once the house warmed up over the course of the day, they would work. My microwave turntable isn't turning. It shows how to remove the touch panel with the Over the Range (OTR) Microwave still installed (as described in my previous post). Check or test each item, starting with the items at the top of the page.
I found a part listed as WB07X10532 called a Frame Control Panel but there is no pic. Thanks! Reply Jim Taylor says: July 7, 2014 at 4:30 pm Thanks for the info this worked for me!! Reply sayaditi says: July 7, 2014 at 11:30 pm This video was helpful… however in my case, I had to tighten the 2 white clips sitting inside the main microwave area The alcohol, warm sponge and hairdryer failed so I used the hairdryer to warm it up.
Dry socks for me tomorrow.DavidOct 2016 Mend it How can i fix my amplifier? Published on Oct 7, 2015 Category Education License Standard YouTube License Loading... Watch Queue Queue __count__/__total__ Find out whyClose GE Cafe Microwave - touch pad not working Colleen Ryall SubscribeSubscribedUnsubscribe5858 Loading... I have reset the ribbon cable from the keypad to the circuit board and checked it for cracks.
Thanks soOoOoOoOo much 4 sharing!!!! Reply V Hilliard says: July 7, 2014 at 6:53 pm thank you! Reply Thomas Nakagawa says: July 7, 2014 at 7:07 pm Thanks a lot for Is it worth the trouble/cost to replace this part and see if it starts working again or should I tras...Click here for the answer